由 activeion 在 05-20-2003 01:19 发表:

着急呀， vsftpd只能用localhost访问，用IP不行

不知道为什么？

步骤：

emerge vsftpd

mv /etc/vsftpd/vsftpd.conf.sample /etc/vsftpd/vsftpd.conf

rc-update xinetd

vi /etc/xinet.d/vsftpd yes--->no

运行/etc/init.d/xinetd

然后

gentoo-jizh root # ncftp localhost

NcFTP 3.1.5 (Oct 13, 2002) by Mike Gleason ([email protected]).

Connecting to 127.0.0.1...

ready, dude (vsFTPd 1.0.1: beat me, break me)

Logging in...

Sorry, I don't do help.

Logged in to localhost.

ncftp / > ls

pub/

ncftp / > quit

You have not saved a bookmark for this site.

Would you like to save a bookmark to:

ftp://localhost

Save? (yes/no) no

Not saved. (If you don't want to be asked this, "set confirm-close no")

gentoo-jizh root # ncftp 162.105.xx.xxx

NcFTP 3.1.5 (Oct 13, 2002) by Mike Gleason ([email protected]).

Remote host has closed the connection.

Sleeping 20 seconds...

由通宝在 05-20-2003 02:30 发表:

肯定网卡没配置好,查一下ifconfig,看看网卡配置文件.

由 activeion 在 05-20-2003 09:21 发表:

my ifconfig , post here

bash-2.05b# ifconfig

eth0 Link encap:Ethernet HWaddr 00:00:E8:7C:BF:F7

inet addr:162.105.51.178 Bcast:162.105.51.0 Mask:255.255.255.0

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:5714 errors:0 dropped:0 overruns:0 frame:0

TX packets:1643 errors:0 dropped:0 overruns:0 carrier:0

collisions:381 txqueuelen:100

RX bytes:1895599 (1.8 Mb) TX bytes:194280 (189.7 Kb)

Interrupt:5 Base address:0xd000

lo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.0.0.0

UP LOOPBACK RUNNING MTU:16436 Metric:1

RX packets:16 errors:0 dropped:0 overruns:0 frame:0

TX packets:16 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:800 (800.0 b) TX bytes:800 (800.0 b)

bash-2.05b#

something wrong?

由 activeion 在 05-20-2003 10:15 发表:

up ,

up . 那位大虾给看看. 有可能哪儿出错了

a test a test

由 Glue 在 05-20-2003 10:56 发表:

贴出你的vsftpd.conf来，

如果你在本机上不能用IP访问，一定是conf有问题

-_-

由 activeion 在 05-20-2003 11:39 发表:

我就用的那个/etc/vsftpd/vsftpd.conf.sample

大家都应该相同的, 我只是试验一下,没有想到根本就不行#

Example vsftpd config file

See man 5 vsftpd.conf for more information.

$Header: /home/cvsroot/gentoo-x86/net-ftp/vsftpd/files/vsftpd.conf,v 1.2 2002/05/04 03:42:50 woodchip Exp $

Allow anonymous FTP?

anonymous_enable=YES

Uncomment this to allow local users to log in.

#local_enable=YES

Uncomment this to enable any form of FTP write command.

#write_enable=YES

Default umask for local users is 077. You may wish to change this to 022,

if your users expect that (022 is used by most other ftpd's)

#local_umask=022

Uncomment this to allow the anonymous FTP user to upload files. This only

has an effect if the above global write enable is activated. Also, you will

obviously need to create a directory writable by the FTP user.

#anon_upload_enable=YES

Uncomment this if you want the anonymous FTP user to be able to create

new directories.

#anon_mkdir_write_enable=YES

Activate directory messages - messages given to remote users when they

go into a certain directory.

dirmessage_enable=YES

Make sure PORT transfer connections originate from port 20 (ftp-data).

connect_from_port_20=YES

If you want, you can arrange for uploaded anonymous files to be owned by

a different user. Note! Using "root" for uploaded files is not

recommended!

#chown_uploads=YES

#chown_username=whoever

Activate logging of uploads/downloads.

xferlog_enable=YES

If you want, you can have your log file in standard ftpd xferlog format

#xferlog_std_format=YES

You may override where the log file goes if you like. The default is shown

below.

xferlog_file=/var/log/vsftpd/vsftpd.log

You may change the default value for timing out an idle session.

#idle_session_timeout=600

You may change the default value for timing out a data connection.

#data_connection_timeout=120

It is recommended that you define on your system a unique user which the

ftp server can use as a totally isolated and unprivileged user.

nopriv_user=nobody

Enable this and the server will recognise asynchronous ABOR requests. Not

recommended for security (the code is non-trivial). Not enabling it,

however, may confuse older FTP clients.

#async_abor_enable=YES

By default the server will pretend to allow ASCII mode but in fact ignore

the request. Turn on the below options to have the server actually do ASCII

mangling on files when in ASCII mode.

Beware that turning on ascii_download_enable enables malicious remote parties

to consume your I/O resources, by issuing the command "SIZE /big/file" in

ASCII mode.

These ASCII options are split into upload and download because you may wish

to enable ASCII uploads (to prevent uploaded scripts etc. from breaking),

without the DoS risk of SIZE and ASCII downloads. ASCII mangling should be

on the client anyway..

#ascii_upload_enable=YES

#ascii_download_enable=YES

#ftpd_banner=Welcome to blah FTP service.

You may specify a file of disallowed anonymous e-mail addresses. Apparently

useful for combatting certain DoS attacks.

#deny_email_enable=YES

(default follows)

#banned_email_file=/etc/vsftpd/vsftpd.banned_emails

You may specify an explicit list of local users to chroot() to their home

directory. If chroot_local_user is YES, then this list becomes a list of

users to NOT chroot().

#chroot_list_enable=YES

(default follows)

#chroot_list_file=/etc/vsftpd/vsftpd.chroot_list

You may activate the "-R" option to the builtin ls. This is disabled by

default to avoid remote users being able to cause excessive I/O on large

sites. However, some broken FTP clients such as "ncftp" and "mirror" assume

the presence of the "-R" option, so there is a strong case for enabling it.

#ls_recurse_enable=YES

由 yongjian 在 05-20-2003 16:26 发表:

broadcast address should not the network address.

由 yongjian 在 05-20-2003 16:28 发表:

inet addr:162.105.51.178 Bcast:162.105.51.0 Mask:255.255.255.0

This link in your network config is probably wrong. The Bcast should be 162.105.51.255.

由 activeion 在 05-20-2003 18:43 发表:

我应该如何修改？

还有一点奇怪的就是：我的ssh server是可以使用的

就是vsftpd不能使用。

由 activeion 在 05-20-2003 18:57 发表:

改好了。但是还是不行。

gentoo-jizh root # ifconfig

eth0 Link encap:Ethernet HWaddr 00:00:E8:7C:BF:F7

inet addr:162.105.51.178 Bcast:162.105.51.255 Mask:255.255.255.0

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:30993 errors:0 dropped:0 overruns:0 frame:0

TX packets:3098 errors:1 dropped:0 overruns:0 carrier:0

collisions:286 txqueuelen:100

RX bytes:5150888 (4.9 Mb) TX bytes:488705 (477.2 Kb)

Interrupt:5 Base address:0xd000

lo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.0.0.0

UP LOOPBACK RUNNING MTU:16436 Metric:1

RX packets:64 errors:0 dropped:0 overruns:0 frame:0

TX packets:64 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:3679 (3.5 Kb) TX bytes:3679 (3.5 Kb)

gentoo-jizh root # ncftp 162.105.51.1

着急呀， vsftpd只能用localhost访问， 用IP不行

Example vsftpd config file

See man 5 vsftpd.conf for more information.

$Header: /home/cvsroot/gentoo-x86/net-ftp/vsftpd/files/vsftpd.conf,v 1.2 2002/05/04 03:42:50 woodchip Exp $

Allow anonymous FTP?

Uncomment this to allow local users to log in.

Uncomment this to enable any form of FTP write command.

Default umask for local users is 077. You may wish to change this to 022,

if your users expect that (022 is used by most other ftpd's)

Uncomment this to allow the anonymous FTP user to upload files. This only

has an effect if the above global write enable is activated. Also, you will

obviously need to create a directory writable by the FTP user.

Uncomment this if you want the anonymous FTP user to be able to create

new directories.

Activate directory messages - messages given to remote users when they

go into a certain directory.

Make sure PORT transfer connections originate from port 20 (ftp-data).

If you want, you can arrange for uploaded anonymous files to be owned by

a different user. Note! Using "root" for uploaded files is not

recommended!

Activate logging of uploads/downloads.

If you want, you can have your log file in standard ftpd xferlog format

You may override where the log file goes if you like. The default is shown

below.

You may change the default value for timing out an idle session.

You may change the default value for timing out a data connection.

It is recommended that you define on your system a unique user which the

ftp server can use as a totally isolated and unprivileged user.

Enable this and the server will recognise asynchronous ABOR requests. Not

recommended for security (the code is non-trivial). Not enabling it,

however, may confuse older FTP clients.

By default the server will pretend to allow ASCII mode but in fact ignore

the request. Turn on the below options to have the server actually do ASCII

mangling on files when in ASCII mode.

Beware that turning on ascii_download_enable enables malicious remote parties

to consume your I/O resources, by issuing the command "SIZE /big/file" in

ASCII mode.

These ASCII options are split into upload and download because you may wish

to enable ASCII uploads (to prevent uploaded scripts etc. from breaking),

without the DoS risk of SIZE and ASCII downloads. ASCII mangling should be

on the client anyway..

You may fully customise the login banner string:

You may specify a file of disallowed anonymous e-mail addresses. Apparently

useful for combatting certain DoS attacks.

(default follows)

You may specify an explicit list of local users to chroot() to their home

directory. If chroot_local_user is YES, then this list becomes a list of

users to NOT chroot().

(default follows)

You may activate the "-R" option to the builtin ls. This is disabled by

default to avoid remote users being able to cause excessive I/O on large

sites. However, some broken FTP clients such as "ncftp" and "mirror" assume

the presence of the "-R" option, so there is a strong case for enabling it.

着急呀， vsftpd只能用localhost访问，用IP不行